DIY white decorative tree with garland. DIY LED tree

Natalia Korpyleva

In the previous post you drew attention to the decoration of the hall for New Year's holidays in our kindergarten.

Our friendly team discussed the design in advance and all groups began to prepare 100 snowflakes per group for the planned curtain of snow-white snowflakes. Soon they were ready.

Teachers of older and middle groups started to decorate wonderful curtain of snowflakes.

We also planned to make two carved multifunctional tree to decorate the hall with illuminated with New Year's garlands and welt patterns.

I took up this matter. For we will need to make wood:floor insulation(the thicker the better, as it holds its shape well, felt-tip pen or a blue marker, a stationery knife or scissors, a bucket or any pot, a piece of thick plastic pipe 1.5 meters, colored tape. transparent tape, Double-sided tape, a little cement and water, a needle and thread white,ruler,New Year's garland, wonderful mood and imagination.

Preparing the barrel in advance tree: wrap the pipe with colored tape, fill the pipe in a bucket with cement diluted in water and leave to harden for a day.

Draw on insulation of the crown of the future tree, attaching the barrel.

Then cut out the second part.

This is what happened.

We draw beautiful patterns with a marker.

Carefully cut out the patterns with a stationery knife.

Fold and trace the patterns with a marker on the other side.

The cut out pieces can also be used to decorate the group.

I cut out patterns.

This is what happened.

Let's cut out this part.

Sew it like this.

Glue pieces of double-sided tape.

Using double-sided tape we glue the part that we will put on the barrel tree. And secure it with transparent tape garland on one side of the crown.

We secure the other half of the crown with tape, sew the two sides together and put it on the trunk.

We decorate the bucket beautifully and this is how carved it is the tree turned out in the end.

Two carved tree fit perfectly into the interior and complemented New Year's decoration hall for the holiday.

During the holiday.

I'm at tree in the costume of Night.

You probably already noticed that at the very beginning of this entry I wrote that tree is a multifunctional decoration for holidays. Its versatility lies in the fact that the crown tree is removed,turned inside out and one side of the crown will be painted in Orange color(to use tree during the autumn holidays, and the other side will be painted in green color (for use during spring and summer holidays).Here it is we got a wonderful tree!

Thank you for your attention! I will be very glad if my idea and my master-The class will be useful to you in your work. Happy New Year to all Maamites! I wish you creative success!

Publications on the topic:

I bring to your attention a tree according to the seasons. I got the idea from the Internet. IN hardware store I bought plastic that can be cut.

Dear colleagues, at the beginning of each academic year the question arises of how to decorate the group. Maam members, ideas and drawings helped me a lot with this.

Good day, dear colleagues! Everyone knows how nature transforms in autumn. Autumn – the artist paints all the trees and bushes bright.

To create our tree of happiness we need to prepare a blank. For her, I cut out a heart 2 cm thick from ordinary foam plastic and put it on.

We need: 2 liter bottle from lemonade, hay, sawdust, twigs, mounting foam - 2 pcs., brown paint, SNOW spray or snowflakes.

Purpose of the lesson: 1. To promote a good atmosphere in the group and friendly attitude of children. 2. Formation of cognitive activity.

Bushes and trees glowing in the dark are a new fashionable trend in lighting technology. Such lamps not only perform their main function - they illuminate the streets in dark time days, but also decorate the city, emphasizing the features of the general atmosphere and placing the necessary accents.

Glowing trees for the street - “useful” splendor

LED trees can be installed almost anywhere, but most often they are unusual lamps flaunt at the entrance to the cafe, shopping mall, restaurant, cinema, boutique, etc. Thus, they become the very attractive highlight that lures visitors to these cultural places.

Glowing bushes and trees are very similar to real ones; they completely imitate the shape of their prototype plant. The metal branches of the LED miracle are covered with artificial bark, and life-size plastic or silicone leaves and flowers are attached to them.

Small single-color or colored LEDs crown this entire structure.

You can, of course, simply decorate an ordinary tree with an LED garland (for example, you can use ), but the effect will not be good enough. What are the advantages of using LED trees?

The photo shows glowing trees against the backdrop of a winter landscape:

Advantages:

• Durability, these lighting serve for at least five years;
• Artificial trees do not require the care that is so necessary in the present;
• Not a large number of electricity consumption, even to illuminate the largest giants requires a maximum of 700 W of energy;
• Easy to install, you can easily do without the help of specialists;
• The design is resistant to influence low temperatures, high humidity and dust;
• If one or more LEDs burn out, the rest of the lamp continues to light, but the LEDs are easily replaced with new ones;
• Properly selected bushes and trees can favorably emphasize the landscape design and become part of the overall decor. Of course you can just use regular ones Street lights for the dacha. You can see the options with photos.

All information about outdoor wall waterproof LED lights you will find.

Types and costs

We said that such trees need to be selected wisely, therefore, the conclusion suggests itself that there are a huge number of their species. LED trees can be different colors and shapes, their size ranges from 0.8 m to 5 m. They are often installed as New Year's decorations.

Palm trees

These exotic trees usually made at least 2 meters in height and can be painted in any color. More simple models made in such a way that the trunk smoothly transitions into spreading branches and its structure and color are identical to the crown. In more expensive palm trees, the texture and color of the pillar is close to natural wood

, and the leaves completely repeat the shape of the real ones. Similar lamps may also differ from each other in the number of branches, the thickness of the trunk, the presence or absence of artificial nuts or fruits. Palm trees are most popular in sanatoriums, boarding houses, hotels and other recreational areas, because they successfully create an atmosphere of sultry fun and the freshness of the sea breeze. The average price of luminous palm trees is 50-160 thousand rubles.

Find out what street ground lamps are.

The weeping willow, glowing in the dark, gives lovers the opportunity to enjoy a date under a spreading tree at any time of the day, without taking their enchanted gaze off each other. This miracle lantern can give a park or square an extraordinary romantic atmosphere, illuminating long alleys and cozy benches.

Here, flexible long branches are attached to a massive trunk, dotted with small leaf-shades, glowing white or any other color of the rainbow. Prices for willows range from 16 to 50 thousand rubles.

Fruit trees For spring to bloom 24 hours a day and 365 days a year, it is enough to install outdoor LED lights in the garden, country house, or just somewhere on the street. fruit trees . Peaches, apple trees, cherries, apricots, pears will delight others with their lush flowering

shades of lilac, white or pink.

On such trees, flowers and fruits are made in life size and look like the inflorescences and fruits of real plants, like twin brothers. The cost of such lamps depends on the chosen tree, its size and the number of branches. This amounts to 12-80 thousand rubles.

Read also about ground LED lamps. Maple Stars glowing in the dark can be found not only in the sky, but also on the LED maple tree illuminating a square or park. Five-point silicone or plastic leaves different sizes on mighty branches - good decision for decoration

public place

, and the paths are visible, and the view is pleasant. The price range of maples is 15-50 thousand rubles.
Sakura This tree can be placed in a special category, since sakura is especially popular. Such trees are especially beautiful; they can transform a simple everyday environment into a fairy-tale kingdom. The branches of these trees are covered with either special high-strength plastic or aluminum alloy, and are shaped in such a way that they closely resemble the real thing. The lantern is strewn with large silicone flowers and leaves, while their density and shape seem to be copied from the real thing. Japanese cherry blossom. Although such trees are made in small sizes, but they give no less light than tall palm trees and spreading willows. The color scheme of sakura LEDs is very soft and delicate in gold, white, pink and purple tones. They cost like this oriental beauties from 5 to 80 thousand rubles. Quite high prices for luminous trees are largely due to the price of

LED bulbs

How to make a glowing tree for the street with your own hands

1. Draw detailed diagram. On a sheet of paper, draw a sketch of the future tree to scale, marking with numbers its height, the length of the branches, the number of luminous elements on each of them and other necessary dimensions.
2. We measure the trunk. Cut off part of the required height from a metal-plastic plumbing pipe or any other pipe - this will be a tree trunk.
3. We make a frame. Cut from wire required amount medium branches and many smaller branches. Bend them into an "L" shape so they can be easily tied to the base. Using black or black electrical tape Brown fasten the small branches to the medium ones, then use the same adhesive material to tape the latter to the trunk.
4. Let's move on to LEDs. Armed with a soldering iron, solder resistors to the LED. Keep in mind that the latter have two legs - one longer, the other shorter. Make sure that all LEDs are soldered either only to the extended or only to the shortened contacts of the resistor. To protect against moisture, a good solution would be.
5. We isolate the LEDs. Take an insulating tube, the color of which matches the shade of the electrical tape, and the diameter is sufficient for the LED to easily fit inside it. Cut the tube, taking into account that the soldering point and the resistor itself should be hidden from the observer, but at the same time it is necessary to leave a place for connection to the power wire. Place the tubes on led light bulbs
6. and heat it slightly with a lighter so that the insulation completely envelops the parts. We attach the LEDs. Wrap each of the LEDs on small branches to the wires according to the polarity and wrap them with insulating tape. Now connect the wiring from small branches to the wires of medium ones, one wire per branch. We connect the bundle of resulting wires again so that all the pluses are together, and the minuses, accordingly, are connected exclusively to each other. The resulting bundles can be immediately soldered to the main wire and run along the trunk, or you can first thread the wires from each branch into pre-drilled holes in the pipe, connect them to each other and solder them to the main wire so that it is subsequently located inside the pipe. Do not forget to observe polarity, and then insulate all exposed conductors. Provide uninterrupted operation at any
7. We decorate the branches. Using leaves and flowers cut out of plastic, decorate the resulting tree, carefully wrap all branches with electrical tape, bringing them as close as possible appearance wood-lamp to natural.
8. We install. The basis for the resulting tree is a barrel, a large pot, a container hidden in the ground, etc. Install your luminous structure into it and connect it to a power source.

Such a tree will especially delight you, like everything that is done with your own hands. You can do many useful things for your site, such as.

The video shows how to make a small glowing spruce. Using the same principle, you can make any other tree:

DIY LED tree - a great opportunity create a fairytale forest yourself, guided only by your fantasy and imagination. At the same time, money is saved. But if you are not very “friendly” with a soldering iron or do not have free time, the best way out is to purchase a ready-made representative of the LED flora.

Currently, there is a huge range of decorative lighting products that are successfully used to decorate rooms and streets. LED trees are becoming especially popular various types, which serve not only as decoration, but also perfectly complement the lighting of buildings and surrounding areas. Thanks to their qualities, they fit perfectly into almost any interior. During the daytime, artificial trees look quite natural, and with the onset of darkness they begin to delight others with all their colors and shades.

There are a large number on sale finished products, however, if you wish, you can make an LED tree with your own hands. An important positive factor is low energy consumption, which is why such trees are increasingly used for decoration in offices, shops and restaurants, attracting the attention of potential customers.

LED tree for home or apartment

Most often when self-production LED trees intended for installation indoors are used in two main ways.

Tree with LED garland

The manufacturing process begins with the frame for which it is best suited aluminum wire. It easily bends at any angle, giving the future structure any configuration. A more realistic color is achieved by wrapping the white insulation of the wire with black electrical tape.

Then, the finished frame is evenly wrapped with a garland, secured to the wire with black electrical tape. If desired, you can create additional decorations for LEDs in the form of decorative attachments from transparent plastic. Upon completion of the work, the manufactured tree just needs to be connected to electrical network and trust its performance. Thus, the question of how to make an LED tree with your own hands can be considered resolved.

The main advantage of this method is considered to be ease of manufacture. The main disadvantage is the impossibility of making wood large sizes. This is due to the standard length of the garland, which is not enough to fit on the entire tree. That's why this method Most suitable for the manufacture of miniature products, which are also very popular.

LED tree

Making a tree from individual LEDs is considered a more labor-intensive process. However, this method does not have the disadvantages inherent ready-made garlands, which allows us to produce structures of any shape and size. The main material is 5 mm LEDs. To equalize the voltage you will need resistors.

Direct manufacturing begins with soldering. LED contacts have different lengths, therefore, the legs of the resistors are pre-shortened, on the one hand. You need to solder the contacts of both elements very quickly so as not to damage the LED.

Heat shrink tubing is then cut into the wires to cover the solder joints and resistors. It is necessary to leave space for soldering the power wire. The tube is inserted onto the resistor leg and heated a little with a lighter to give the insulation the required shape. This operation performed with each LED.

After this, you can begin making the tree itself. Most often, the trunk is made of thin plumbing pipes, and the branches are made of wire, approximately 50 cm long. The main part of the branch takes 45 cm, and 5 cm is left for attaching it to the trunk. Small branches are cut into sizes up to 10 cm. The number of LEDs on one branch must be calculated in advance.

At the next stage, small branches are tied with electrical tape to large branches. The number of LEDs on each small branch is recommended to be made equal to the number LEDs on a large branch. Each LED is secured using electrical tape.

The wires need to be stretched along the entire length of the main branches, after which they are cut taking into account the bends of the small branches. The ends are wound to the trunk, after which all the pros and cons on each branch are connected. Their number should match the total number of branches. The wire connections are insulated. All that remains is to hang it evenly decorative ornaments and connect the finished tree to the electrical network.

LED trees for outdoors

Artificial trees with LEDs can be installed in any place to decorate the landscape and surrounding areas. The attractive power of beauty actively attracts visitors to restaurants and cafes, shopping centers and boutiques, offices and other public places. Each glowing tree their configuration largely resembles real plants, and sometimes completely imitates them. Artificial bark is used to cover metal branches. Maximum resemblance can be achieved thanks to silicone or plastic leaves and flowers made in life-size.

The entire structure of the artificial tree is decorated with multi-colored LEDs. Most often they operate from the electrical network, but in some cases autonomous power supply can be used, which leads to a slight increase in the cost of the design. Sometimes LED garlands are used, but they do not give the same effect as LEDs used separately.

Advantages of artificial trees with LEDs:

• Long service life of at least 5 years.
• Artificial structures do not require the maintenance required by real trees.
• Low power consumption. Even the largest trees consume electricity in quantities not exceeding 700 W.
• The simplicity of the design allows you to install it yourself, without involving specialists.
• Resistance of the structure to low temperatures, dust, high humidity and other negative influences.
• If one or more LEDs burn out, the rest of the chain will continue to work, and faulty elements can be easily replaced with others.
• Right choice artificial trees and bushes allow you to favorably emphasize and complement the elements.

Particularly popular among led plants Sakura enjoys. These trees are especially beautiful thanks to the highly durable coating of the branches with plastic or aluminum alloy. Their appearance is as close to the real thing as possible. Despite its relatively small size, this tree gives as much light as more tall structures. Sakura has a soft and delicate light spectrum, mainly white, pink and golden tones.

Making your own wood for the street

When making wood with LEDs for outdoor use, be sure to take into account the aggressive influence environment. Therefore, before you start making an LED tree for the street with your own hands, you need to determine the entire procedure in advance.

The general scheme of work will be approximately the same as for conventional designs intended for indoor use. IN street version It is recommended to pay attention to more thorough covering of the trunk and branches with high-quality materials.

It is also necessary to take care of good insulation of the LEDs after soldering them with resistors. Heat shrink tubing should completely hide each pair. If necessary, all unreliable areas can be additionally insulated with black electrical tape. The same goes for wire connections in the plus and minus areas. Decorative items should be secured more efficiently so that they are not torn off by strong gusts of wind.

Master class: DIY glowing tree

It’s completely in vain to remove the glowing garland after the winter holidays. There are a lot interesting ways decorating your home interior with it.

1. Place a garland around the edge of the mirror of some interesting shape.

2. Wrap paper lanterns and garland around a branch and hang above your bed.

3. Create a cascading light by decorating the garland with large bulbs.

4. Create an original tree from a garland.

Draw an outline on the wall, drive carnations around the perimeter and wrap a glowing garland around them. As easy as pie!

5. Attach photos to the glowing garland using clothespins.

6. Create your own canvas with a pattern of glowing lights.

7. Thread the garland into flower baskets or place it directly there.

8. Fill wine bottles with lights to effectively illuminate them from the inside.

9. Create an angel wreath using paper napkins.

Using wire cutters, form a round snowflake holder and wrap it with an electric garland with small bulbs. Then glue decorative snowflakes onto the holder.

10. Or use napkins to make a wedding wreath.

Just do it small holes in napkins and thread lights through them.

11. Cover disposable cardboard cups with unusual paper; this will help create interesting light shades using an LED garland.

12. Crochet a glowing rug using rope and garland.

13. Decorate your Christmas garland with tulle bows.

14. To create a festive mood, decorate the garland with old ornaments.

15. Create colorful balls of twine and decorate them with glowing garland.

16. Make flaming snowflakes using store-bought bouquet holders.

17. Intertwine a rope with a garland for a nautical-themed room decor.

18. Create a network of glowing garland in your bedroom.

19. Hang air clouds with a dangling glowing garland.

The photo shows a two-dimensional version of the cloud.

20. You can also use egg cartons to create a floral effect.

21. Write a letter-by-letter message on pendant lights.

Make letters by punching holes in the paper.

22. Create a romantic headboard.

Knock down a layup wooden frame and add crossbars. Drill small holes and insert rosettes into the bottom of each niche. Paint the frame and screw it to the wall. Fill each niche with garland and connect it to the outlets. Cut transparent panels from polycarbonate sheets and attach them to the frame using fasteners.

23. Use glitter wrapping paper to create giant glowing candies.

Required materials and tools:

• disposable Plastic container with lid;
• electric garland;
• scissors;
• wire or pipe cleaners;
• wire cutters;
• multi-colored wrapping paper;
• scotch.

Preparation method:

1. Cut a piece of wrapping paper measuring 45x45 cm from the roll.
2. Wrap the garland with wrapping paper. Don't forget to leave both ends of the garland outside in order to connect it to the network and connect the element with other candies.
3. Place the wrapped garland in a plastic container and seal it. Wrap the container with wrapping paper and secure with tape.
4. Using pipe cleaners or wire, shape the container with the garland into a candy shape.
5. Decorate the entire garland in this way, leaving free space (20-40 cm) between the links.
6. Connect the finished bunch of candies to the network.

24. Insert lanterns into tiny preserving jars.

Take special lids with a hole for the garland. Close each jar with a lid and insert a garland light bulb into it.

25. Insert an LED string light into an old toy.

You will need:

• old toy (made of cotton fabric);
• PVA glue;
• brush;
• scissors;
• threads;
• light garland.

Preparation method:

26. Write a light message.

27. Arrange the glowing garland in a wave-like pattern.

28. Cut out black cat shapes to make this cute garland.

29. Wrap the garland around a wire wreath.

Probably one of the most simple options creating homemade wreaths.

30. Light up the canopy over the bed with garland.

31. Cut the paper into strips to create the same fringed lanterns.

32. Use foil from a muffin tin as a garland decoration.

This is a great idea for any party.

33. Create sparkly decorations with mirrors and lighting.

Take:

• brushed aluminum rod;
• hooks for hanging;
• a garland with mirror pendants;
• electric garland.

Instructions:

1. Attach the rod to the wall using two hooks.
2. Hang a mirror garland on the barbell. To enhance visual effect You can trim some of the threads with pendants so that the finished curtain is of different lengths.
3. Stretch a string of lights behind the pendants and connect it to an outlet.

34. Use twigs to create a rustic chandelier.

This idea can easily be implemented with a luminous garland.

Take:

• dry branches;
• hemp twine;
• stain (optional to darken the color of the wood);
• wood color paint;
• lamp sockets with a removable cardboard cover for painting;
• plastic ties;
• glue gun;
• electrical cable black and white;
• black electrical wire with fork;
• Branch squeezes "nuts".

Instructions:

35. Make a garland of geometric lanterns.

You can make your own lanterns from black wire or natural straw.

Bushes and trees glowing in the dark are a new fashionable trend in lighting technology. Such lamps not only fulfill their main function - illuminating the streets at night, but also decorate the city, emphasizing the features of the general atmosphere and placing the necessary accents.

Glowing trees for the street - “useful” splendor
LED trees can be installed almost anywhere, but most often such unusual lamps are displayed at the entrance to a cafe, shopping center, restaurant, cinema, boutique, etc. Thus, they become the very attractive highlight that lures visitors to these cultural places. Glowing bushes and trees are very similar to real ones; they completely imitate the shape of their prototype plant. The metal branches of the LED miracle are covered with artificial bark, and life-size plastic or silicone leaves and flowers are attached to them. Small single-color or colored LEDs crown this entire structure. Such ornamental trees can be powered by the network, but more often they are equipped with an autonomous power supply, which makes the structure somewhat more expensive. You can, of course, simply decorate an ordinary tree with an LED garland (for example, you can use street garlands on solar powered), but the effect will not be good enough. What are the advantages of using LED trees?

Advantages: Durability, these lighting devices last at least five years; Artificial trees do not require the maintenance that real trees require; A small amount of electricity consumed, even to illuminate the largest giants requires a maximum of 700 W of energy; Easy to install, you can easily do without the help of specialists; The design is resistant to low temperatures, high humidity and dust; If one or more LEDs burn out, the rest of the lamp continues to light, but the LEDs are easily replaced with new ones; Properly selected bushes and trees can favorably emphasize the landscape design and become part of the overall decor.

These exotic trees are usually made to be at least 2 meters tall and can be painted in any color. Simpler models are made in such a way that the trunk smoothly transitions into spreading branches and its structure and color are identical to the crown. In more expensive palm trees, the texture and color of the pillar are close to natural wood, and the leaves completely repeat the shape of real ones. Similar lamps may also differ from each other in the number of branches, the thickness of the trunk, the presence or absence of artificial nuts or fruits. Palm trees are most popular in sanatoriums, boarding houses, hotels and other recreational areas, because they successfully create an atmosphere of sultry fun and the freshness of the sea breeze. The average price of luminous palm trees is 50-160 thousand rubles.

Find out what street ground lamps are.
The weeping willow, glowing in the dark, gives lovers the opportunity to enjoy a date under a spreading tree at any time of the day, without taking their enchanted gaze off each other. This wonderful lantern can give a park or square an extraordinary romantic atmosphere, illuminating long alleys and cozy benches. Here, flexible long branches are attached to a massive trunk, dotted with small leaf-shades, glowing white or any other color of the rainbow. Prices for willows range from 16 to 50 thousand rubles.

Here, flexible long branches are attached to a massive trunk, dotted with small leaf-shades, glowing white or any other color of the rainbow. Prices for willows range from 16 to 50 thousand rubles.
For spring to bloom 24 hours a day and 365 days a year, it is enough to install outdoor LED fruit trees in your garden, country house, or just somewhere on the street. Peaches, apple trees, cherries, apricots, and pears will delight others with their lush blooms in shades of lilac, white or pink. On such trees, flowers and fruits are made in life size and look like the inflorescences and fruits of real plants, like twin brothers. The cost of such lamps depends on the chosen tree, its size and the number of branches. This amounts to 12-80 thousand rubles.

Maple glowing
Maple Stars glowing in the dark can be found not only in the sky, but also on the LED maple tree illuminating a square or park. Five-pointed silicone or plastic leaves of different sizes on powerful branches are a good solution for decorating a public place, and the paths are visible and the view is pleasant. The price range of maples is 15-50 thousand rubles.

public place
This tree can be placed in a special category, since sakura is especially popular. Such trees are especially beautiful; they can transform a simple everyday environment into a fairy-tale kingdom. The branches of these trees are covered with either special high-strength plastic or aluminum alloy, and are shaped in such a way that they closely resemble the real thing. The lantern is strewn with large silicone flowers and leaves, and their density and shape seem to be copied from real Japanese sakura. Although such trees are made in small sizes, they provide no less light than tall palm trees and spreading willows. The color scheme of sakura LEDs is very soft and delicate in gold, white, pink and purple tones. Such oriental beauties cost from 5 to 80 thousand rubles. The rather high prices for luminous trees are largely due to the price of LED street lighting lamps (more details here) that are used in their manufacture.

How to make a glowing tree for the street with your own hands

1) Draw a detailed diagram. On a sheet of paper, draw a sketch of the future tree to scale, marking with numbers its height, the length of the branches, the number of luminous elements on each of them and other necessary dimensions.

2) We measure the barrel. Cut off part of the required height from a metal-plastic plumbing pipe or any other pipe - this will be a tree trunk.

3) We make a frame. From the wire, cut the required number of medium branches and many smaller branches. Bend them into an "L" shape so they can be easily tied to the base. Using black or brown electrical tape, secure the small branches to the medium ones, then use the same adhesive material to tape the latter to the trunk.

4) Let's move on to the LEDs. Armed with a soldering iron, solder resistors to the LED. Keep in mind that the latter have two legs - one longer, the other shorter. Make sure that all LEDs are soldered either only to the extended or only to the shortened contacts of the resistor.

5) We isolate the LEDs. Take an insulating tube, the color of which matches the shade of the electrical tape, and the diameter is sufficient for the LED to easily fit inside it. Cut the tube, taking into account that the soldering point and the resistor itself should be hidden from the observer, but at the same time it is necessary to leave a place for connection to the power wire. Place the tubes on the LED bulbs and lightly heat them with a lighter so that the insulation completely envelops the parts.

6) Attach the LEDs. Wrap each of the LEDs on small branches to the wires according to the polarity and wrap them with insulating tape. Now connect the wiring from small branches to the wires of medium ones, one wire per branch. We connect the bundle of resulting wires again so that all the pluses are together, and the minuses, accordingly, are connected exclusively to each other. The resulting bundles can be immediately soldered to the main wire and run along the trunk, or you can first thread the wires from each branch into pre-drilled holes in the pipe, connect them to each other and solder them to the main wire so that it is subsequently located inside the pipe. Do not forget to observe polarity, and then insulate all exposed conductors.

7) Decorate the branches. Using leaves and flowers cut out of plastic, decorate the resulting tree, carefully wrap all branches with electrical tape, bringing the appearance of the tree-lamp as close as possible to the natural one.

8) Install. The basis for the resulting tree is a barrel, a large pot, a container hidden in the ground, etc. Install your luminous structure into it and connect it to a power source

Such a tree will especially delight you, like everything that is done with your own hands. You can make many useful things for your site, such as do-it-yourself birdhouses.

A DIY LED tree is an excellent opportunity to create a fairy-tale forest yourself, guided only by your fantasy and imagination. At the same time, money is saved. But if you are not very good with a soldering iron or do not have free time, the best way out is to purchase a ready-made representative of the LED flora.