Starline a 93 how to set the clock. How to correctly set the time on a Starline alarm key fob

In many devices, when replacing the power element (battery, accumulator), a complete data reset occurs. If the battery on the Starline A91 alarm key fob is replaced, the time is reset, after which it must be set again. But not everyone knows how to set the time, and this is required when using the timer function.

Modern car alarm system

Have been in use for many years modern systems car alarm. Once it was a luxury, but now it is convenience and safety. Car alarms are a 12 volt device. Has interactive authorization. Each alarm has its own encryption keys. They also have a function for remotely starting the car engine according to the time set on the timer or starting is carried out according to the temperature readings of the internal combustion engine (when the engine temperature drops below the specified one, the engine starts).
The interactive authorization function protects the car owner from hacking, which is carried out using an electronic reader. Resistant to the latest code grabbers thanks to conversational codes and a new frequency hopping method.
Methods of such protection, this method of data encryption are used in two control panels: the main and the additional. The StarLine A91 alarm device has good resistance to low temperatures. Works great in a temperature range from -45 to +85 degrees.

Functions that are capable of performing and are the same. The only differences are in the operating range, reliability, and ease of use.

Pros of StarLine A91

This alarm model is reliably protected from hacking, because it uses a new data encryption method. But, attackers are also constantly improving equipment for stealing alarm codes - .
There is a Megapolis mode. It should be used in densely populated areas where there is a lot of radio interference.
It is possible to start the engine in different ways.
The device is Russified.
Thanks to modern software, the response speed of the Starline A91 alarm is 20% greater than the speed of operation of the same devices, but previous models.

How to set up Starline A91 key fob

Remote control, keychain remote control can perform several functions, namely:

Setting the current time on the device display.
Activation of the set alarm time.
The ability to turn it on and off.
Ability to set countdown timer.
The ability to activate the function of starting or shutting down the internal combustion engine.

How to set the time on Starline A91:

Press and hold button No. 3 on the key fob. The third button is used to change the time. You should hold this button until such sound signals: one long melody - short signal - 2 short beeps. When it's three sound mode passed, the time display starts flashing. Button No. 1 should be used to increase the time, No. 2 to decrease it.
After the time has been set, you need to hold button No. 3 for a while to proceed to setting the minutes. As soon as the minute indicator starts blinking, we adjust the minute values using buttons No. 1 and No. 2.
Then, press button No. 3 again to set the alarm time. We also hold it until the alarm starts flashing and set the time with keys No. 1 and No. 2.
Next, you need to adjust the minutes of the alarm clock. Again, hold button No. 3 until the minute indicator blinks and also set the desired values.
Then, by briefly pressing button 3, the alarm clock turns on or off.
When you press the 3rd button further, the timer setting mode is activated. When the timer indicator blinks, set the desired value.
If you press button 3 again, you can also edit the minutes of the timer using buttons 1 and 2.
If you press the third button again, the timer will turn on or off. The first button turns it off, the second turns it on.

As you can see, there is nothing complicated in setting the alarm time. This applies not only to this model, but also to setting up key fobs different models car alarms.

Video

This video shows how to set the time on the Starline A91 alarm key fob

And in this video, in more detail, how to disable the Starline A91 alarm

And finally, the Starline autorun timer

Setting the clock, timer and alarm car alarms Starline necessary for precise activation of functions in time. For example, to use remote automatic engine start. you can do it yourself using the user manual.

[Hide]

Instructions for setting the time

The procedure for setting the time on the Starline key fob may differ depending on the alarm model.

How to set and set the time on the remote control:

Take the pager and hold down the key under the third number, it is used to adjust the alarm system clock parameters. Press and hold the key until the key fob speaker emits one melodic pulse. After this, another short beep will sound, and then two more short melodies will sound. This indicates successful entry into the clock programming mode. The indicator with a clock on the signaling key fob will blink. Using the key under the first number, the hour values are increased, and using the second button this parameter can be decreased.
Then briefly press the third key to set the minutes. This will cause the minute indicator to blink on the display. Key 1 increases the minutes, and button 2 decreases them.
After this, click on key 3, this will cause the pager to enter the alarm clock parameters activation mode. When the corresponding indicator starts blinking, the first button increases the readings, and the button number two decreases them.
Click the key again to set the alarm minutes. The procedure for increasing and decreasing parameters is performed in a similar way.
With a subsequent short click on key 3, you can activate or deactivate the alarm clock. Button 1 “signals” turns on the function, and key number 2 turns it off.
If you further press the key number 3, the alarm timer setting menu will open. When the option indicator starts blinking, the first and second keys decrease or increase the parameters. When you next briefly click the third key, the minute indicator will flash. The value is adjusted using similar buttons. After setting, pressing key number 3 will activate or disable the option.
To leave the clock setting mode, you simply do not touch the buttons on the pager for five seconds.

Irina Belousova showed how to independently set the time on the Starline pager.

How to set the time on the key fob, E91, B94:

To enter the setup menu, you need to click and hold down key number 4. The button is held until the security system pager emits one long and then two short beeps.
After this, you will hear another long and two short beeps. On the pager screen you can see the indication of the first option. Using the first and fourth keys, you select the required function. F1 is used to adjust time and date settings.
Having selected an option, click on the fourth button and hold it until two short beeps sound.
Specify the adjustment option. The pager allows you to set not only the minutes and hours, but also the day, month and year. To select the desired value, click on the fourth or first key.
Once a parameter is selected, the values are adjusted by using the second and third buttons.
When all the values have been set, you need to exit the setup mode. The alarm will automatically go off if you do not click on the pager buttons for eight seconds. You can exit the settings menu by holding down the first transmitter button. Exit from the mode will be indicated by two short-term pager signals.

Reasons for settings failure

If the control device displays the wrong time, then first of all you need to diagnose the battery condition in the pager. All remote controls of modern Starline security systems are equipped with an option to indicate battery charge. When the battery loses its capacity and cannot perform its main function, a discharge indicator will appear on the screen. In addition to the icon on the display, the remote control will emit a characteristic melodic signal.

The cause of the failure may be the replacement of the battery. When a new battery is installed in the pager, it automatically resets the time. Please remember that replacing the power source will reset the alarm's anti-burglary protection parameters. After you change the battery, you need to activate the security mode. Only then is it possible to set temporary indicators. The problem of settings failure may be due to the fact that the car owner made mistakes during adjustment.

Andrey Sharshukov showed how to adjust the time values on the key fob from the Starline A93 complex.

Trouble-shooting

To fix the problem, you need to diagnose the key fob and, if necessary, change the power sources. If the malfunction was a failure of the pager itself, then the device must be repaired or replaced.

After eliminating the cause of the malfunction in the Starline key fob, you will have to re-adjust the clock readings.

There are two options:

Traditional. Setting time parameters is carried out according to the instructions described above.
Radical. The power supply in the pager is replaced at 00-00. All time parameters will automatically be reset to zero, and the time will begin to count from the specified point.

What happens if you don't set the clock?

The remote engine start options may malfunction. The power unit of the car will not be able to start on time by an alarm clock, after a certain time interval or by a timer. After implementing the remote start option, the power unit will remain unheated, which is due to increased loads may cause damage to the starter device.

Setting the time on the key fob is necessary for a reason: the alarm system has the ability to automatically start the engine using a timer. You can do everything working week go out to an already warmed-up car without making any effort - and park the car so that it has a stable connection with it.

The site employs an auto electrician-diagnostician, a certified StarLine specialist. If you have questions about car alarms, ask them at the end of the article in the comments or on Vkontakte.

Setting the clock

To enter the configuration mode for the key fob itself, press and hold button 4: first the key fob will give one signal, after a pause – 2 more. After that, release the button. The hour display will start blinking - set the desired hour by increasing the number with button 2 or decreasing with button 3. Then briefly press 4 - the minutes will start blinking, set them in the same way.

By pressing 4 again, you will go to setting the alarm time - set the hours, then the minutes in the same way. The next press on 4 will switch the key fob into the alarm on/off mode: if you set it to ON, the key fob will sound an alarm every day at the previously set time. Select desired setting and press 4 again - now set the autorun timer.

The principle of setting the autorun time does not change - set the hour and minute, press 4 and then turn on the timer (ON) or disable autorun by timer (OFF).

You can also activate the timer launch in the second way, and there will be some differences in the operating algorithm:

Press and hold button 2 or 3 until you hear a long beep followed by a short beep.
The alarm clock icon will start blinking on the screen in the bottom row. If you press button 1, it will light up constantly, buttons 2 and 3 will switch to the adjacent icon.
To exit this mode, hold button 1 for a long time until the signal sounds.

What is the difference? If the alarm icon is displayed on the screen, then autostart will not occur at the time set by the timer, but at the time for which the alarm is set. If you activate the icon “ hourglass", then it will occur starting from the time you activate this mode and then every few hours. What is it for? In cold weather, this mode of operation allows the car not to get cold, and it is used on diesel cars, or when spending the night in the car in winter. To set up periodic autorun, you need to activate the hourglass and set the key fob timer and set the correct interval.

As soon as you activate the hourglass, the display on the screen will change: initially the inscription 4H will appear, and further short presses on button 1 will change the inscription to 6H, 8H and so on up to 24H. Periodic engine starts will occur at intervals of 4 hours, 8 hours, and so on. When you exit setup mode, the engine will start automatically.

Video: Setting the time on the starline a 93 alarm key fob (without unnecessary information)

Car alarms have a wide range of functions, including not only security systems. Not everyone can set the time on the Starline A93 key fob using buttons.

In addition to the standard engine shutdown, door, hood and gearbox locking, Starline car alarm owners have access to many secondary functions.

The system can turn on a timer for the turbine. After active driving on turbocharged engines, some elements of the intake tract heat up to about 800 degrees Celsius. Cooling occurs due to motor oil circulating through the system. Therefore, turning off the turbo engine immediately after aggressive driving is not recommended. Turning on the turbo timer – useful feature, depending on the clock.

You can set an alarm clock and auto-start on it. This setup will be one-time only. Setting an alarm clock is convenient if the owner is going to do unusual things after hours (pick someone up from the airport, meet someone from the train station). At the set hour, the Starline key fob will play the wake-up melody, and then give a command for auto-warming. During daily use, you will need to constantly restart the system: go into Top Menu(clock-alarm-timer), and then set the alarm to activate again.

Instructions: how to set the clock on the Starline A93 key fob with 3 buttons

Some alarm key fobs have only three keys. You can set the time on your Starline device like this.

Press and hold button 3 until the sound signal sounds.
Then the clock indicators will flash. With keys 1 or 2 we can increase or decrease the value.
Then press button 3 of the Starline key fob again to switch to the minutes setting mode. Set the desired value.
You don't have to press anything to confirm the command. After five seconds, the menu will automatically exit and specified values will remain in the alarm memory.

Setting the clock with 4 buttons

The main Starline A93 alarm remote control has four keys. Therefore, the standard procedure for setting the time looks like this.

You should make sure that there is a battery inside the Starline alarm key fob and that the remote control is functioning properly and the keys are not blocked.
Press and hold button number four until one melodic signal sounds. Then two more short sounds will follow, indicating that the key fob has entered the time setting mode.
The value will now start blinking. You can set the appropriate number of hours using button two or three. The first key of the Starline key fob increases the value, the second one decreases it. After setting, press button four again, going into the minutes setting mode.
The procedure for setting minutes is carried out in a similar way - by holding down keys two or three on the Starline key fob.
The next press allows you to configure alarm functions or settings.
Exit from the Starline programming mode is automatic after 8 seconds. You don’t have to press anything; the set time parameters will be saved automatically.

Reasons for settings failure

Sometimes the Starline A93 alarm system presents unpleasant surprises. Among the various “glitches”:

door unlock failure;
lack of command transmission from the Starline remote control;
Resetting time or autorun settings.

There are several reasons for the failure.

Car battery malfunction. If it is very discharged, it may not receive signals sent from the Starline tuning remote control. The machine's battery must be replaced for normal operation.
Wiring short circuit. Because of incorrect connection Starline A93 car alarms may have problems. Another reason is a broken or frayed wire on the road, which contributes to short circuit. To eliminate the problem, you will need the help of a car electrician at a specialized service.
The reason may be the Starline keychain itself. You should inspect it for mechanical damage - there should be no breaks or chips of plastic, cracked screen or other faults.
Dead battery. The signal, as well as the time setting, may be lost due to a faulty battery in the Starline setting key fob. It is necessary to open the compartment and inspect it. The battery should not be swollen, and the remote control contacts should not have traces of oxides or rust. Otherwise, you need to install a new battery and clean the contacts. To prevent such situations, it is advisable to change the battery in advance - approximately every 3-4 months. Should be installed nutritional elements from trusted brands.

If a malfunction occurs, glitches appear or the time is reset, it is advisable to reset the Starline alarm parameters to factory settings. To do this, you need to know the location of the Valet service button, which is installed when installing a car alarm.

It allows you to enter Starline programming mode, start the car without a key fob, etc. That’s why they hide it. If you do not know the exact location of the service button, you should check these locations:

under the dashboard;
on side maps;
behind the decorative covers of the center console;
under the sun visor.

Once the button is found, you can begin resetting Starline to factory settings.

Turn off the ignition.
Press the service key 9 times to reset the first programming table.
Turn on the ignition. The vehicle will emit nine beeps and lights to indicate that it has entered the appropriate mode.
To completely reset it is worth carrying out the procedure twice - the second time you need ten clicks on the button to reset the second table.
After finishing, you need to press the service key, and then listen to one siren signal.
Click K1 on the Starline key fob. The machine will beep to indicate a return to standard settings.
Turn off the ignition. The car will flash the emergency lights three times, indicating the successful completion of the procedure.

Setup video

How to configure and set the time on the StarLine A91 key fob? Detailed manual

Quite often, after replacing the batteries in the control panel, owners do not know how to configure and set the time on the StarLine A91 key fob. Especially for owners of such devices, we will briefly talk about this, so that many who encounter such a problem can independently set the current time on the display. It is important to perform this operation correctly, since many owners use a timer to start the engine.

Configure and set the time on the StarLine A91 key fob possible for any driver, regardless of driving experience. The development of this model of car security alarm fully meets the requirements of car owners to ensure their safety. Therefore, the key to ensuring the correct and long-term use of such a system is to study the instructions for its operation.

A few words about the security system

These developments security systems They are among the most modern and reliable 12 Volt devices, have interactive authorization, encryption keys are individual for each product, and have a function such as remote start according to a set time on the control panel timer or engine temperature. Performance is maintained even in conditions of strong radio interference in urban areas.

The use of interactive authorization eliminated the possibility of intelligent electronic hacking and provides high resistance to all code grabbers known today. This became possible after the use of conversational encoding algorithms, using individual encryption keys, as well as a new, previously unused frequency hopping method.

This encryption method is used for both control panels, both for the main key fob and for the additional one. The existing system fits well with machines that also have such a button. The device has good resistance to changes in outside air temperatures. High performance is maintained at temperatures from minus 45 degrees to plus 85 degrees.

Benefits of using it

- The product is highly resistant to hacking attempts, thanks to the use of new encryption methods;

- The presence of the Megapolis mode allows the use of products in places with big amount radio interference;

- You can use several different ways remote engine start;

- All inscriptions and pictograms are made in Russian;

The use of modern software developments has made it possible to achieve an increase in the speed of operation of devices by approximately 20% compared to other models of similar devices.