Do-it-yourself tire sculptures step by step instructions. Crafts from tires: flower beds, flower beds, figures, garden furniture

( ArticleToC: enabled=yes )

Tire recycling has become an integral part of our lives. Everyone solves this problem in their own way. Tire car for the playground! Many people like this idea.

The kids are just delighted with such crafts, and adults look with admiration. Given that the tires are resistant to negative external influences, this design will please the eye for more than one year.

Parents with small children will need a little time to arrange a playground in the country or on the street and do not need any financial expenses. And the kids will play without distracting their parents from important matters.

You can make crafts for such a site yourself, even if you have never done this before. Ideas and order of work can be peeped on the Internet. More often, plastic bottles and tires are used to make them. There is nothing difficult in manufacturing.

The main thing is desire and a little time.

You will not need to spend money on purchasing expensive materials, since car service workers will gladly give tires, which usually accumulate a sufficient amount of them. What craftsmen just don’t make from tires: swings, sports equipment, flower beds, etc.

Types of cars

Transport is a constant success among boys, and even modern girls. Therefore, you can start by making a car for children. A tire car for a playground can be of various brands (types) - from very simple to quite complex.

Instructions for making a car from wheels

The easiest option would be to dig a steering wheel from a real car and a seat into a square of tires.

The place for the site where the craft will be installed is better to choose a lighted, spacious, located near the house. The best coverage would be a backfill of sand or a lawn, which will have to be cleared of stones and glass in order to protect the kids from injury.

Shop machine

It won't be hard to make it. To do this, having cleaned and painted the board well, it is fixed between tires of the same size. These will be the rear wheels. In the same way, you can do the front. But you can install only one wheel in the center so that the craft resembles a racing car.

The depth of the pits for the wheels of the car should be such that the latter are hidden up to the disk. Then the transport will be stable. After filling them with earth, tamp it well. It is better to dig in tires with disks. But, if they are not there, you can replace it with plywood to give the structure rigidity.

Linoleum is used to simulate the floor, but it can be replaced with plywood. So that the linoleum does not pick up the wind, it is advisable to dig the steering wheel into the ground through it. The tilt of the steering wheel is selected in accordance with the growth of a particular child.

Tire Truck

You can make a children's sandbox in the form of a truck.

Seat manufacturing

The seat can be made from one tire or by putting two on top of each other.

In the simplest version, they are limited to mounting on plywood tires. If you want to make it more comfortable, you need a back. You can upholster the seat with something soft - foam rubber, carpet, blanket.

A plastic chair that is not used at home is suitable, wooden seats from chairs, old chairs. Having sawed off the legs, they are fixed, fixing with self-tapping screws.

Details are washed and dried well before painting. After that, a brand new car is painted in the preferred colors.

To give the craft a greater resemblance to the original, headlights are added. They fit jar lids.

And the next model is for the kids of the whole yard, because it allows a big company to go.

What else will help to make it look like a real car?

The doors attached to the craft will undoubtedly make the craft look like a real car. To play with a machine for a large number of children, they make several rows of seats (2-3). If there is an extra tire, make a spare tire, attaching it to the back and writing the number with paint.

The roof to the car, covered with linoleum, in addition to giving a resemblance to a real car, will protect from sunlight and light rain. To fix it, you will need wooden bars, folded in the form of the letter "P". All you need is 3 pieces. Two structures are installed in the rear above the machine (it is better to dig them into the ground), the third is closer to the front. They are connected with bars from above to get a horizontal frame, on which linoleum is fixed with screws or nails from above.

For a racing car, you need to find 5 tires of the same size. A little work of parents and they will turn into a wonderful car that will not leave a child indifferent.

Three tires are enough to make a car, as in the photo below. On it, little racers will not be able to rush through the expanses of the planet, but they will play with pleasure.

For "cool" kids, you can make a motorcycle. The truth will have to be imagined. But the happy faces of the owners of such bikes will be a reward for caring parents.

Video: Racing car made of wheels, tires.

Car owners know the value of tires. What a pity to throw them away after they have served their due date. Previously, 20-30 years ago, in the schoolyards, one could see old tires that were used to equip flowerbeds and physical education. If you show imagination, you can independently make many interesting crafts from tires.

In the 80s and 90s of the last century, in rural areas, children rode on a swing made from old car tires. And this is not the only thing that can be built from this material. It is very easy to make crafts from car tires, the main thing is to arm yourself with patience, the necessary tools and a sufficient amount of material.

Crafts from tires for the garden

The summer cottage is the place where you can make any dreams come true and make crafts from tires with your own hands. In order to make a figurine from an old tire, you need to choose a suitable place, decide on a task, prepare a tool and get to work. You can spend from 3 to 5 hours of free time on creating simple crafts, but you will have to take several days to create more complex designs.

What materials and tools will be needed:

• sharp durable knife;
• hacksaw for metal;
• electric jigsaw;
• metal ruler;
• rope;
• paint brush;
• paints of different shades;
• strong wire;
• bolts;
• tires.

It is easier to work with imported tires - they are not so thick, they are easy to cut and bend well. When choosing tires, you should pay attention to the type of tires - a winter tire will turn out much easier than a summer one.

Tires can be used to make many useful items. For example, a tire hedge will look good in the garden, separating the site or dividing it into several zones: work, for games and recreation. You can diversify landscape design with beautiful elements or build a table and chairs from tires.

Look at this image, making such a kit yourself will not be difficult. The only thing to adhere to is not to bring such furniture into the room, since even an old car tire will emit an unpleasant smell of rubber. But for outdoor gatherings - such furniture will come in handy:

You can also decorate the garden plot with interesting crafts: make containers for growing climbing plants out of tires, install small pots or adapt rubber buckets.

Look at this image - such a composition will decorate any garden and save space:

How to make a flower garden from a tire

A budget option for creating flower beds from tires can be found in almost any yard. Car tires are built in structures (ring, fence, wave) and painted with multi-colored paints. There are many options for creating flower beds from tires. The technology is simple: the tires are buried halfway into the ground, and the middle is covered with earth and flowering plants are sown.

Complex structures, for example, a flower garden, can be done like this:

1. It is necessary to prepare car tires of different diameters. Large tires will be used as a flower bed, and small tires will serve as a fence.
2. Dig the tires into the ground, and set the small ones upright.
3. To prevent small tires from falling, they need to make a transverse incision and “plant” them on both sides in large tires. From below, to make the structure stronger, you can fasten the rubber with wire or metal staples.
4. You should get a chain of tires.

Small islands-beds of tires in the form of tulips look beautiful. To create such a flower bed, you need to prepare 1 car tire with a disc.

How to make a tulip flower bed:

1. Step back from the disk 1 cm and draw a contour with chalk (these will be the petals).
2. Cut the tire around the perimeter of the wheel (without removing it from the disk) along the contour.
3. Separate the parts and unscrew the tire - you will have a bowl on the stop.
4. To give a beautiful look to the flower bed, paint the tire with multi-colored paints and draw patterns.
5. After complete drying, the flower bed will be ready.

It is easy enough to make a flower bed in the form of a swan. To create a figure, you need 1 car tire. Look at the diagram to understand how to cut a tire and make a swan neck:

The finished figure must be painted with white paint. After the paint has dried, earth is poured into the middle of the flower bed and plants are planted.

Another option for creating a decorative figurine from car tires. For work, it is better to use old "bald" car tires and a sharp knife. Use this diagram to draw lines with chalk along which it will be more convenient to cut out the shape.

Step by step creation of a swan figurine:

1. Cut out the wings of the swan along the lines with a sharp knife or electric jigsaw.
2. Since this part of the work is very difficult to perform, it is necessary to prepare a sharp knife with a wide blade in advance.
3. To make it easier to cut the rubber, during operation, you need to moisten it in a soapy solution.
4. We unscrew the cover. We make small holes in the body of the swan and in the neck area with a screwdriver or hand drill to fasten the parts together with wire.
5. We give the figure a shape, cut out the eyes and beak. We attach the parts with screws.
6. We paint the swan white, leave the eyes black, and paint the beak red.

How to make crafts from tires - watch the video:

Make 2 tire figures and place them near a miniature pond, which can also be created from an old car tire.

To make a small pond yourself, prepare the following tools and materials:

• wide tire;
• electric jigsaw;
• shovel;
• building level;
• crushed stone and sand;
• waterproofing film.

How to make a mini pond:

1. Prepare the site - the site should be flat, without a slope.
2. Dig a hole with a shovel to place the tire in.
3. Lay the tire inside and check its location with a building level.
4. Sprinkle rubble on all sides.
5. Now you can use an electric jigsaw to cut off the side parts.
6. Lay a waterproofing layer, lay crushed stone and sand along the contour of the tire, press the edges tightly.
7. To close the film, lay out the edges of the reservoir with a decorative stone.
8. It remains to fill the artificial reservoir with water.

Children's town from car tires

With the help of old car tires, you can build a whole children's town. Consider the popular options for using tires:

1. Children's sandbox. You don’t have to spend a lot of effort on creating a sandbox, you need to dig the tire halfway into the ground, revive the sandbox by painting it with bright colors and filling it with sand.

1. Children's swing. What else to do with the baby in the country? Of course, you can ride a swing, and you can make them from old car tires. Just cut the tire in half, cut out the inside, leaving room for seating below, and hang the finished swing with a strong rope. Little kids will love the colorful hanging swing in the form of a flower or a horse.

1. Rocking chairs. You'll have to work hard to make a baby rocking chair. The work is divided into the following stages:

• tire preparation - cut the tire so as to get 2 identical parts;
• seat preparation - cut out a board of the desired size, attach it to the tire;
• decor - paint the seat and base in bright colors.

1. Cars, boats, horses, caterpillars. Kids really like to explore new figures - turn the steering wheel, sit on a horse. From old car tires you can make a small car with a real steering wheel, headlights and seats.

Crafts from tires can be seen in the photo:

What else can you do with old tires?

Human fantasy has no limits. Incredibly, from old tires you can build not only beautiful figurines for the garden, flower beds and equip a playground. It is easy to make garden furniture or a dog bed out of tires. See how beautifully and tastefully you can decorate a cozy corner for relaxation:

Using an old bicycle tire, you can make a stylish bracelet or a durable belt that will serve the owner for many years:

And here is another interesting idea - you can upholster an old chest with a rubber sheet from a car tire. Such furniture will look very original, and you won’t have to spend much effort. It is necessary to cut the canvas and nail it with small carnations. Get an exclusive item!

And in order to create such a figure, you need to familiarize yourself with the elements of artistic carving and be patient. Not everyone can make such a masterpiece:

Tire beds

Almost everyone has seen flowerbeds and flower beds made of tires - in the simplest version, when the tire is used without any special modifications, they are in any yard. But the fantasy of folk craftsmen does not stand still.

With the help of simple improvised tools, the tire can be turned into a large flowerpot.

DIY flowerpot made from an old tire with a disk. It must be cut with a knife or a small grinder. To do this, put the tire on the ground and cut around the entire perimeter on the side of the tread. The tire should be cut without removing it from the disc. Then turn inside out both the bottom and the top. Thus, you have a kind of glass, the sides of which can be cut and various pebbles, shells, etc. can be glued to them. You can also paint it with different colors. Here everything depends on your imagination. Then you can plant flowers in the middle. It will take you no more than two hours to make such a flower bed.

Enlarge image

Flower bed from a tire in the form of a swan with a cutting pattern:

Flowerbeds from ordinary tires. It seems to be nothing special, but the tires are arranged in certain compositions, combined with the environment and therefore look good:

Decorating a summer cottage is a creative and exciting task. At the same time, it is not necessary to buy expensive sculptures or other finished works of art. It is enough to show ingenuity, imagination and perseverance to get beautiful figures from improvised materials. In this article, we will look at how crafts for the garden are made from tires.

Ideas for decorating your summer house

The use of old tires allows you to manage the interior design of your garden with virtually no investment. The finished price will be negligible, and the family budget can be spent, for example, on improving living conditions. So, what can be created from the mentioned material?

Example #1: swan

For all crafts, you will need approximately the same list of materials:

And tools:

Instructions for creating a swan:

1. We draw with chalk the lines along which the tire should be cut. Do it as shown in the photo or find suitable patterns on the Internet.

1. Carefully cut the rubber.

1. "Bulgarian" we cut the part that did not succumb to the knife.
2. We turn the product, bending the cut edges.

Tip: if the craft is made for the children's part of the garden, then it is necessary to carefully process the sharp edges of the cut elements, otherwise the child may be injured about them.

1. We paint the swan in the desired colors.

Using various patterns, you can get not only swans, but also a wide variety of other garden crafts from car tires.

Example #2: caterpillar

In this option, you don’t even have to cut anything, but you will need a little more materials:

We proceed as follows:

1. We partially bury the tires in the ground, connecting them with self-tapping screws.
2. From above we fasten the bar bent in the form of a mustache.
3. We fasten empty cans in front.
4. We paint the figure and get a slightly surprised, but quite attractive insect.

Example #3: bear cub

To get a clubfoot beast you will need:

Work progress:

1. We make holes in the large and small tires with the help of a "grinder" so that they can be connected with a pipe.
2. We close the holes of the tires with pieces of plywood, which we fix with self-tapping screws.
3. We glue linoleum on plywood.
4. We cut out ears and paws from thick rubber, after which we fix them in the right places.
5. We put the resulting figure on two small wheels, which will play the role of a kind of legs.
6. We paint the craft in two layers.

Example #4: Giraffe

Not enough exotic in your country house? Build a giraffe! For this you will need:

It doesn't take much to work on it:

1. Bury the tire halfway into the ground.
2. We knock down a log and a chock with nails in the likeness of a neck and head.
3. We bury the resulting structure next to the tire.
4. We cut out the ears from plastic and fasten them to the head with nails or glue.
5. We glue the eyes from the toy on the face of the resulting beast.
6. At the back we fix a piece of a watering can as a tail.
7. We give the appearance of a giraffe with the help of paints.

Example #5: Crocodile

A toothy predator can also perfectly decorate your site. For this are used:

Here you will need some carpentry skills:

1. We cut the tire, cutting out the body of the crocodile.
2. We cut out the shapes of the back and abdomen from the boards, fix the slats as spacers as shown in the following photo:

1. We insert the resulting frame inside the back and fasten it with screws.
2. From below, in the same way, we fix the stomach of the future crocodile.

1. We screw plastic teeth into the “mouth”.
2. Glue the scales.
3. Insert table tennis balls into eye sockets.
4. We color the craft in green color.

Practical use of tires

Products from tires for the garden can have a practical value in addition to decorative value.

Here are a few options for their use:

1. Vases for flowers. The tire is cut and turned out, after which it is filled with earth and a plant.

1. Swing . Here you can experiment from the banal hanging of a whole product to cutting out bizarre shapes. (See also the article.)

1. Arrangement of sewer wells. Tightness and moisture resistance make tires an excellent cheap material for creating walls of septic tanks or other similar structures.

1. Children's sandboxes. To do this, just enough to dig the tire and fill it with sand. Minimum costs, and the child will already have a place to play.

1. Steps. If the terrain on your site has a slope, then it can be equipped with tires, which will greatly simplify its overcoming.

1. Bicycle stands. Bury the tires halfway into the ground next to each other, and you can conveniently put bikes between them.

1. Fencing. With tires, you can easily enclose the desired area, break its zones.

1. Sports and game equipment. It can be an obstacle course or just a product dug into the playground, on which the kids will happily climb.

Conclusion

As you can see, old car tires should not be rushed to be thrown away. With their help, the summer cottage can be turned into a real amusement park. These can be both decorative crafts in the form of various animals, and quite functional objects.

The main thing is to use your imagination correctly and put some effort into arranging your garden. Above are some solutions to such a problem.

The video in this article will provide you with additional information that is directly related to the materials presented. Creative thinking and old wheels will allow you to ennoble your own cottage almost for free.

Almost everyone has a car and if you take care of your car sooner or later old unnecessary tires will appear. Many people leave them at service centers, service stations, or simply store them in the garage. But few people know that old tires can be given a new life and useful things can be made from them: garden furniture, swings, planters, flower beds and beautiful decor items. And in this article I want to tell you about interesting and useful do-it-yourself crafts from car tires.

"Caterpillar"

To decorate your garden or yard, our craft is a very cute caterpillar made from car tires. This craft will also become an original flower bed. She will delight you with her appearance and give a smile.

You will need:

• Tires for automobiles - 7 pcs.
• screwdriver
• self-tapping screws
• Dye
• Plastic bottles - 8 pcs. (1.5 - 2 liters)
• Plastic bottles - 2 pcs. (0.5 liters)
• glue moment
• Scissors
• Shovel

How to do:

1. The first step is to paint the tires bright green and let them dry.
2. When the tires are dry, you will need to fasten them together with a screwdriver and self-tapping screws. We fasten only 7 pieces.
3. Dig a trench for the future caterpillar. At the beginning, the tire should fit into the trench by 70%, then we reduce the depth of the trench so that the last tire goes deep into the ground by 30%. Thus, our tires on the surface are at an angle.
4. We take the remaining tire and cut off the side court on one side to the tread pattern.
5. We attach the cut tire to the body, using a screwdriver and self-tapping screws, so that we get a mouth.
6. From six bottles, we cut off the bottom and fasten it to our caterpillar with self-tapping screws as shown in the photo.
7. From two large bottles we will cut out the eyes. To do this, cut the bottle in half and make cuts to the bottom to get cilia - 6-8 pieces. The rest of the walls of the bottle are cut off to the bottom.
8. We fix the eyes on the first tire with self-tapping screws.
9. For small bottles, we also cut off the bottom and glue it into the eyes with the convex side out.
10. Next, we fill the earth in the tire-mouth and plant flowers. Our caterpillar is ready!

DIY tire chair

For beginners, I want to offer a fairly simple car tire craft, which will become a cozy and comfortable chair in your home or country house. In order to learn how to make such a chair with your own hands, see our master class with step-by-step instructions, photo and video description.

You will need:

• Car tires — 2 pcs.
• screwdriver
• Long screws
• Felt
• Construction stapler
• Plywood
• furniture foam
• Piece of thin foam

Progress:

1. We put the tires one on top of the other and fasten them with self-tapping screws.
2. With felt, you need to close the bottom of the chair, using a stapler. We do this in order to later make it easier to move it around the floor.
3. From the furniture foam we cut out a circle as the outer part of the tire and insert it inside the upper tire. This will require some effort.
4. We put a circle of thin foam rubber on top and fix it with a stapler.
5. Plywood needs to be bent along the contour of the tire and attached in a semicircle to make a back.
6. We wrap the entire surface of the back with thin foam rubber and fix it with a stapler.
7. Now take a blanket or bedspread and put it on a chair in the form of a cover. To create the look of the cover, you need to fix it on all sides with a stapler.

Tire bed

If you want to decorate your garden with flowers, then such a flower bed is ideal for this purpose. She herself looks like a big flower and will serve as an additional, but not the last decor of your garden. Working on such a craft requires time and effort, but the result will please you. Let's see a step-by-step instruction with a full description of how to make a flower bed of tires with your own hands.

You will need:

• Car tire with disk
• File
• Paint any color
• soapy water

Progress:

1. You need to put the tire with the disk on the ground and use chalk to draw a pattern in the form of sharp petals.
2. Now, with the help of a sharp knife, we proceed to cutting. To make it easier to cut, moisten the cut with soapy water.
3. Now the most difficult thing is to turn it out, it is not so easy to do it, you have to try. Carefully turn it out in a circular motion, fixing the already bent edges. Better to help you.
4. You will get a vase on a leg from a disk with openwork edges.
5. Wash the tire thoroughly with soap to remove dust and dirt.
6. Let the tire dry and you can apply paint on it. It is advisable to have several flowers on hand, this will make the flower bed more colorful.

Palm

The palm tree is a symbol of summer, sea and warmth. And with the help of it, you can create an unusual mood and it will not seem to you that you are not on your site, but on the sea. Let's start doing our crafts with our own hands.

You will need:

• Car tire — 3 pcs.
• wooden pole
• Twine
• soap solution
• screwdriver
• Long screws
• Paint (green)
• Shovel
• small wooden square

Progress:

1. We dig a post into the ground, in the place where you need to install a palm tree.
2. We wrap the pole with twine in dense rings, fixing it with glue. We will have a trunk.
3. We nail a wooden square to the top of the pillar.
4. Color the square green.
5. We cut the tires in half across the court, while moistening with soapy water.
6. Cut out palm leaves from the halves of the tire. You should get 6 pieces.
7. Paint the leaves green.
8. We fasten the leaves to the crown of the trunk with the help of self-tapping screws. Palm is ready!

Tire swing

For your child, you can make a tire swing without spending a lot of time and effort, and the child will be very pleased. You can make such a swing in your yard, in the country or in the area so that your baby is not bored.